Thanks for those measurements, and we do have Solera slide toppers for your 79-1/4 inch, 85 inch, and 86 inch slides, which are the following parts:
- 79-1/4": Solera RV Slide-Out Awning - Black # LCV000168105 or White # LCV000163285 (note: the product pages say these are for 74" - 79" wide slides, but they are technically for 74" - 79-3/4" slides)
- 85": Solera RV Slide-Out Awning - Black # LCV000165062 or White # LCV000163287
- 86": Solera RV Slide-Out Awning - Black # LCV000168106... view full answer...
If your current inner bearing is a 25580 with a 1.75 inch ID, the outer bearing is 14125A with a 1.25 inner bearing and the bolt pattern of your current hubs is 8 on 6-1/2, the Dexter Axle 42866UC3-EZ 7K hub you'd looked at would be the correct replacement. The hub uses a GS-2250D grease seal, which has a 2.25 inch ID which matches what you found with your existing hub/drum.
You can indeed reuse the existing castle nut and cotter pin, and the # AKEBRK-7-SA self-adjusting brake assemblies... view full answer...
If the frame members are further apart than 72 inches, we don't have a frame mounted hitch that would work.
If the fifth wheel has a 4 inch square steel bumper, a bumper mounted receiver like # E-100 would be a good choice. The hitch has a 350 lb tongue weight capacity which would be limited by the capacity of the bumper if its lower.
If you click the link, you can see a video featuring the bumper mount hitch I recommended. view full answer...
Based on the brackets you have near the suspension of your Open Range 3X 375RDS 5th wheel trailer your best option for a shock kit will be a Lippert kit that doesn't take up as much space as the Roadmaster kit you referenced.
For that you'd want the # LC281255 for if your trailer has 3,500 lb axles that are 2-3/8 inch in diameter or the part # LC281281 which fits axle diameters of 3 inch like what are found on 5,200 to 7,000 lb axles.
Also thanks for clarifying what the brown foam was.... view full answer...
We have the Ceiling Garnish for Ventline Roof Vent # Item # VA0445-29 which has rounded corners and is Birch white which is an off-white color. I attached a review video for this for you to check out as well. view full answer...
I have a solution for you, but you'll need to take a few things into consideration to determine whether or not this will work for you.
You could use a hitch like the Curt Adjustable Width Trailer Hitch Receiver for RVs # 13703 which is designed for trailer and RV frames 22"-72" wide and has a 3500-lb towing capacity. This hitch can be mounted on the frame of your Open Range 427BHS, however I would first consult with your trailer's owners manual to determine whether or not the frame is... view full answer...
After replacing The Printed Circuit Board for MaxxAir MaxxFan Plus Roof Vents # MA10A04751KS, and the motor still does not open the lid you will need to replace the motor. The Replacement 12-Volt Variable Speed Fan Motor for MaxxAir MaxxFan RV Roof Vents # MA10-20968 will replace the 12-volt DC variable-speed fan motor on your MaxxFan 4791KS.
I attached a review video link below. view full answer...
We don't have the specs for your specific trailer's wheel pilot hole. There are two common sizes for the just over 3 inch caps. We have the 3.19 inch option like # 319EZ and the 3.33 inch option like # AM90195.
The best way to know which you need is to use a digital caliper like # PTW80157. view full answer...